Fischer

Product Details:

The fischer high-performance mortar FIS V Plus is the universal all-rounder for the highest requirements. The styrene-free vinyl ester hybrid mortar with its numerous fixing elements is approved for fixations in cracked and non-cracked concrete as well as in masonry. However, the injection mortar is also used with the approved system components for rebar connections, the fischer remedial wall tie VBS 8, the fischer weather facing wall tie FWS II, and the stand-off installation system TherMax. The variant FIS VS Plus Low Speed enables an extended processing time at higher processing temperatures or a greater drill hole depth. The shorter hardening time of the variant FIS VW Plus High Speed enables swift work progress even at low temperatures.

Advantages

• The FIS V Plus injection mortar has numerous system approvals, such as in cracked and non-cracked concrete, ma­sonry and for special applications.
• The ETA assessment for a service life of 100 years offers permanent safety for all applications.
• The approved use in water-filled drill holes enables a wide range of applica­tions, even under harsh environmental conditions.
• FIS VW Plus High Speed has a significantly shorter hardening time than FIS V Plus, which ensures swift work progress even at low temperatures.
• The FIS VS Plus Low Speed has an extended processing time that prevents the premature hardening of the mortar at higher temperatures. It is ideally suited to large drill hole depths.
• The extensive range of accessories is ideally suited to the FIS V Plus injection mortar family, increases the great flexi­bility of the system and thus allows for a broad range of applications.

Applications

• Steelwork constructions
• Timber constructions
• Guard rails
• Façades
• Staircases
• Steel brackets
• Machines
• Masts
• Awnings
• Canopies
• Gates
• Consoles
• Pipelines
• Gratings
• Satellite antennas

Approved for anchorings in:

• Concrete C20/25 to C50/60, cracked and non-cracked
• Hollow blocks made from lightweight concrete
• Hollow blocks made from concrete
• Vertically perforated brick
• Perforated sand-lime brick
• Solid sand-lime brick
• Aerated concrete
• Solid brick

Approved for:

• Rebar connections
• Remedial wall tie VBS 8
• Weather facing reconstruction system FWS II
• Stand-off installation TherMax

Permission

• ETA-20/0603
• ETA-20/0728
• ETA-20/0729
• DoP 0231
• DoP 0232
• DoP 0233
• ESR-2786
• 20046/15515
• 22044

Functionality

• FIS V Plus is a 2-component injection mortar based on a vinyl ester hybrid concept.
• Resin and hardener are stored in two separate chambers and are not mixed and activated until extrusion through the static mixer.
• The mortar is extruded bubble free from the drill hole base.
• The mortar bonds the entire surface of the anchor with the drill hole wall and seals the drill hole.
• The injection cartridges are quick and easy to use with the fischer dispensers.
• Partially used cartridges can be reused by changing the static mixer.

Product Details:

• FIS EM Plus with optimised formulation for improved load values in cracked and non-cracked concrete.
• The ETA assessment guarantees a service life of 100 years, an external expert report even up to 120 years.
• For rebar connections from diameter 8 to 40 mm.
• Can be used with threaded rod FIS A or internal threaded anchor RG M I for temporary and removable fixing points.
• FIS EM Plus is to be processed at temperatures down to -5°C.
• More safety due to approvals for diamond drilled and water-filled drill holes as well as seismic applications of performance categories C1, C2.
• The approval of the injection mortar for use in glued laminated or glued solid timber of spruce (Picea abies), fir (Abies alba) or pine (Pinus sylvestris) allows the realisation of high-performance and appealing wood-wood, wood-concrete and wood-steel connections.

Product Details:

    The fischer hammerset anchor EA N is an internal thread anchor made from zinc-plated and stainless steel. The hammerset anchor is ideal for the multiple fixation of non-structural systems that do not require approved anchorage. The assembly of the internal thread anchor is extremely cost-effective thanks to the low embedment depth, fast hammerset installation, and direction-controlled screwing process. The EA N is mounted with the hammer flush to the base material. With the setting tool EA-ST, the sleeve is expanded and braced against the drill hole wall through the driving in of the internal pin. No torque should be applied to the screw to enable correct expansion.

Advantages

• Simple hammerset installation
• The metric internal thread allows for the use of standard screws or threaded rods for ideal adaptation in line with the intended use.
• The hand setting tool EA-ST facilitates fast installation.

Applications

• Pipelines
• Cable trays
• Consoles

Building materials

• Concrete C12/15, non-cracked
• Concrete C20/25, non-cracked

Functionality

• The EA N is suitable for pre-positioned installation.
• Position the hammerset anchor in the drill hole and drive in flush to the surface of the base material using the hammer.
• The setting tool EA-ST is then used to expand the sleeve against the drill hole wall by driving in the internal pin.
• The setting tools must sit on the edge of the anchor to ensure correct expansion.

Product Details:

The fischer anchor rod RG M is a system component for use with the fischer resin capsules RSB and RM II and the fischer injection mortars FIS SB, FIS EM Plus, FIS EB II, FIS V Plus, FIS VL, FIS V Zero, FIS P Plus or FIS P. Due to the oblique edge, it is particularly suitable for use with the resin capsules RSB and RM II. The extensive assortment in diameters M8 - M30 and in different steel grades enables extremely diverse applications. The system is particularly suitable for the cost-effective fixation of railings, steelwork constructions, and advertising systems both inside and outside. The RG M is set with the bonded anchor setting tool and a hammer drill using rotating and hitting motions. During the resin capsule setting process, the capsules are destroyed by the characteristic oblique edge and are mixed, and the mortar is activated. The approvals of the various resin capsules and injection mortars must be observed.


Advantages

• The wide range of the RG M from M8 to M30 opens up a wide range of applications and therefore offers great flexibility.
• The wide range of approved steel types for RG M allows for use in all corrosion resistance classes and offers the best possible application safety.
• Please refer to the approvals for the resin capsules and mortar used.

Applications

• Anchorings with resin capsule RSB, RSB mini and RM II
• Anchorings with each of the fischer injection mortars such as FIS SB, FIS EM Plus, FIS EB II, FIS V, FIS VL, FIS V Zero, FIS P Plus, FIS P and FIS EP

Building materials

• In connection with the fischer resin capsules approved or suitable for cracked and non-cracked concrete.
• In connection with several fischer injection mortars approved or suitable for different building materials.

Approvals

• ETA-02/0024
• ETA-19/0501
• ETA-20/0603

Functionality

• Due to its oblique edge, the anchor rod RG M is particularly suitable for use in conjunction with resin capsules.
• The anchor rod RG M is set using a hammer drill and the accompanying setting tool in rotating and hitting motions.
• During setting, the oblique edge of the RG M destroys the capsule, and mixes and activates the mortar.
• Use with injection mortar is also possible. Here, the anchor rod is manually inserted into the drill hole with a light rotating movement until it reaches the base of the hole.

Product Details:

The fischer threaded rod FTR is a cost-effective system component without approval for the fischer resin capsules RSB and RM II and for fischer injection mortars. For single fixations, the application with the pre-portioned resin capsule is particularly cost-effective. The hot-dip galvanised and zinc-plated steel threaded rods enable extremely diverse applications. The system is particularly suitable for cost-effective fixations indoors where no approval is relevant. The FTR is set with the bonded anchor setting tool and a hammer drill using rotating and hitting motions. During the resin capsule setting process, the capsules are destroyed by the characteristic oblique edge and are mixed, and the mortar is activated.

The advantages / Product descriptionAdvantages

• The threaded rod FTR is the cost-effective solution for applications with resin capsules where no approval is required.

Functionality

• Due to its oblique edge, the threaded rod FTR is particularly suitable for use in conjunction with resin capsules.
• The threaded rod FTR is set using a hammer drill and the accompanying setting tool in rotating and hitting motions.
• During setting, the oblique edge of the FTR destroys the capsule and mixes and activates the mortar.
• Use with injection mortar is also possible. Here, the threaded rod is manually inserted into the drill hole with a light rotating movement until it reaches the base of the hole.